CISCO 7912G PDF

Note For each Cisco IP phone that you install in your network, you must first make some critical decisions about how to configure the phone in your network. You can then safely install the phone and verify its functionality. By doing this, users gain access to web pages that allow them to configure phone options such as call forwarding and speed dialing. To see translations of these warnings, refer to the Regulatory Compliance and Safety Information for the Cisco IP Phone Series document that accompanied this device. Warning Read the installation instructions before you connect the system to its power source. Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Author:Brajora Nele
Country:Dominica
Language:English (Spanish)
Genre:Business
Published (Last):17 December 2017
Pages:444
PDF File Size:13.35 Mb
ePub File Size:1.1 Mb
ISBN:897-8-32268-220-6
Downloads:73393
Price:Free* [*Free Regsitration Required]
Uploader:Kagarisar



Additional Configuration Methods, Parameters, and Procedures. The Cisco IP Phone must be correctly configured before it will operate properly.

When you configure a phone, you specify parameters and values that instruct the phone how to operate in your environment. Configuring provides the phone with instructions for many aspects of its operation, including how to interact with the network and how to handle IP telephony protocols. These processes are described in detail in this manual.

These methods are optional and are available to help you configure your phones most efficiently and to provide certain configuration options that are not available through other methods. A profile file is a binary file that contains a list of tag, length, and value triplets TLVs that represent some of the configuration parameters for the Cisco IP Phone.

You can edit a text version of a profile file and then convert it to a binary file for the phone to download. In these file names, each xx is the two-digit lowercase hexadecimal representation of each integer in the phone's MAC address.

If the ff xxxxxxxxxxxx, ld xxxxxxxxxxxx, or gk xxxxxxxxxxxx profile file does not exist, the Cisco IP Phone G will try to download the profile file ffdefault. The ffdefault. The TFTP server stores the common profile file lddefault. The Cisco IP Phone G profile file name is ff xxxxxxxxxxxx , where each xx is the two-digit lowercase hexadecimal representation of each integer in the phone's MAC address.

The file name must be exactly 14 characters. For example, if the MAC address is 0. Note Profile file names begin with "ld," which is a lowercase "L" followed by a lowercase "D. You can edit a profile file in text format on the TFTP server and then convert it to the binary format required by the phone. See the "Creating or Updating a Profile File" section for more information.

Configuration parameters are entered in the format "Parameter:value. See the "Configuration Parameters" section for more information about parameters and values. You can obtain the latest version of this file from the CCO website. Note A profile file for your phone may contain some parameters that are not described in this manual. These parameters are reserved for future use or are configured with factory default settings and should not be changed. Before you can create a new binary profile file, you will need the cfgfmt.

The cfgfmt. This file specifies the type and size of each parameter. It is recommended that you use the ptag. You can also obtain them from the CCO website. For a description of profile file parameters, see the "Configuration Parameters" section.

Specify this path if the ptag. See the "About Profile Files" section for profile file name requirements. You can access the web page using any graphically capable web browser. Note It is recommended that you take care to prevent unauthorized access to a phone's web page. It is also recommended that you increase security by setting a password using the UIPassword parameter in the phone's profile file.

If you want to edit parameters in the Network Parameters, Tone Parameters, or Audio Parameters areas, you must first set up a password with the UIPassword parameter in the profile file.

If you do not set up a password, you will be able to view information in these areas, but you will not be able to change parameters, and Apply will not be available. For more information, see the "Device Information" section. For more information, see the "Network Configuration" section. For more information, see the "Network Statistics" section.

For more information, see the "Device Logs" section. For more information, see the "Network Parameters" section. For more information, see the "Tone Parameters" section. For more information, see the "Audio Parameters" section. If you have set up a password with the UIPassword parameter in the profile file, enter the password in the UIPassword field, and then click Apply.

If you want to change the password, enter the new password in the two ChangeUIPassword fields before clicking Apply. Make changes to parameters in the Network Parameters, Tone Parameters, and Audio Parameters areas as needed and lick Apply to save your changes.

Possible states include:. See the "Network Parameters" section. See the "Tone Parameters" section. See the "Audio Parameters" section. See the "Profile File Parameters" section. Note Do not specify a port number. Specifies whether the phone contacts the DHCP server to obtain values for various network parameters, including IP address, router IP address, and subnet mask.

Domain name on the network in which the phone operates, used in the creation of the endpoint identifier. For example, if the name of the endpoint is aaln1 and the domain is cisco. Set 0 or 0. Enter the extended IP address of the server to which troubleshooting messages are sent and collected in a log file. Note To collect troubleshooting messages, the prserv. For more information about using Nprintf and preserv. Bits 0 - 7—Interval between each call-waiting tone. The range is 0 to The setting 0 specifies the factory default.

Any other number specifies the interval in 0. The default setting is 0x64, 10 seconds. Bits 28 - 29—First repeat interval for the Volume and Navigation buttons. That is, the button takes effect the first time a user presses and holds down the button for the interval specified. The default value is 0. Bits 30 - 31—Subsequent repeat interval for the Volume and Navigation buttons. For example, the volume increases or decreases when a user continues to hold down the Volume button for the interval specified.

Three comma-separated integers, a , b , c , where:. Comma-separated string of nine integers, a through i. See the DialTone parameter for a description of these integers. Note For this parameter, the value for total duration of tone specifies the number of samples at 8, samples per second. Tone that confirms successful completion of an operation such as call forwarding.

If 1, enable G. The default setting is 1. If 1, use both G. Must be set to 0. If you have Cisco ITS, refer to the documentation for that product. Determines the precedence and delay of sent IP packets.

Enter an even number from 0 to Each connection uses the next available even-numbered port for RTP. Password for accessing the phone's Change Configuration web pages or to unlock the phone's Network Configuration screen for editing. After a password is set with this parameter, the password can be changed from the phone's web page.

For more information, see the "Web Page Configuring" section. Note Changing a password from the phone's web page does not change the password in the profile file. If the phone downloads the profile file, the password will be reset as specified in the profile file. Allows you to specify the graphic that appears on the phone's LCD screen. To provide upgrade instructions in this way, add the following line to the Cisco IP Phone profile file:.

This value must be different for each upgrade. For this value, it is convenient to use 0x followed by the build date on the image file name. You can access the IVR system through the Menu button on your phone.

The following table lists the IVR menu codes. Use these codes when you navigate the IVR system using your keypad. The codes of settings that you will probably use most often are numbers 1, 2, 10, 20, 21, 22, 23, 24, and For more information about these settings, see the "Configuration Parameters" section.

Numeric input includes numbers from , and may include periods. Alphanumeric input includes numbers from , alphabetic characters, both uppercase and lowercase, and symbols.

When entering alphanumeric input, use the dial pad and press a number key the appropriate number of times to access the correct letter, number, or symbol you need, followed by the sign, and another sign to complete your input.

ABRAHAM LINCOLN CAZADOR DE VAMPIROS PDF

Cisco Unified IP Phone 7912G - Retirement Notification

The Cisco G provides core business features and addresses the communication needs of a cubicle worker who conducts low to medium telephone traffic. Availability: In Stock. Learn about our Certified Refurbished products. Our Certified Refurbished products are fully tested, factory defaulted, and remanufactured to a high quality, factory like new condition. We change plastics, add factory finished tops, and replace button sets, labels, overlays, handsets, and cords on all of our Certified Refurbished phones. Better yet, we back them with a Rock Solid 1 Year Warranty , superior service, and expert technical support. Pixel-based display provides intuitive access to calling features 4 soft keys dynamically present calling options to the user Menu key for quick access to information such as call logs and phone settings Hold, volume control Call monitor speaker only, no microphone Powered by local 48VDC power supply sold separately, see option above or power down the LAN by Cisco Discovery Protocol CDP Pre-loaded with SCCP for Cisco users.

KUBLER ROSS ETAPAS DEL DUELO PDF

Cisco 7912G IP Phone (CP-7912G=)

.

Related Articles