This guide also provides mounting instructions and limited troubleshooting procedures. Translated versions of the following safety warnings are provided in the translated safety warnings document that is shipped with your access point. Note The access point is suitable for use in environmental air space in accordance with section You should not install the power supply or power injector in air handling spaces. Note Use only with listed ITE equipment.
|Published (Last):||27 April 2015|
|PDF File Size:||19.82 Mb|
|ePub File Size:||18.80 Mb|
|Price:||Free* [*Free Regsitration Required]|
Quick Links. Table of Contents. Obtaining Documentation and Submitting a Service Request. Declarations of Conformity and Regulatory Information. Wlc wireless lan controller , wism wireless services module integrated wlc with aps 40 pages.
Cisco aironet series lightweight outdoor access point 40 pages. Aironet series ieee This guide also provides mounting instructions and limited troubleshooting procedures. Safety Instructions Translated versions of the following safety warnings are provided in the translated safety warnings document that is shipped with your access point. Page 3 Warning Installation of the equipment must comply with local and national electrical codes.
Ensure that the protective device is rated not greater than: 20A. Statement Warning Do not operate your wireless network device near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for Page 4: Verifying Shipped Components Return any packing material to the shipping container and save it for future use.
Step 2 Step 3 Verify that you have received the items shown in Figure 1. If any item is missing or damaged, contact your Cisco representative or reseller for instructions. Figure 1 Shipping Box Contents Figure 2 shows the access point key components. Page 6: Performing A Site Survey Cisco recommends that you make a site map showing access point locations so that you can record the device MAC addresses from each location and return them to the person who is planning or managing your wireless network.
Note Set up a terminal emulator on your PC to communicate with the access point. Use the Page 9: Configuring Basic Settings Mounting the Access Point Cisco Aironet , , , , and series access points can be mounted in several configurations, including on a suspended ceiling, on a hard ceiling or wall, on an elecrtical or network box, and above a suspended ceiling. Page 10 If required, configure the power settings as described in the previous section.
Otherwise, Click Step 4 Express Setup. The Express Setup page appears. Page 11 Configure the settings using the following sections as a guide. The system name appears in the titles of the management system pages. The workgroup bridge must associate to a Cisco Aironet access point or bridge. This illustration shows the Express Security page.
Static WEP keys are vulnerable to attack. Cisco access points use hexadecimal characters. Client adapters can use either, depending on how the vendor chooses to configure them. Click Apply. A login and Step 1 password screen appears.
Enter the username Cisco and password Cisco. The username and password are case sensitive. Step 2 Step 3 When the access point does not receive enough power for full operations, it is in low power mode.
Page 21 Set the power settings and power injector fields, and verify your switch status as shown in Step 5 Table 3. To verify switch status, you need to use the switch CLI.
Page Access Point Specifications Select the section that best suits your troubleshooting needs. Step 8 Access Point Specifications Table 4 lists the technical specifications for the series autonomous access point. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. Within the 5. These guidelines are provided in both Japanese and English. Japanese Translation English Translation This equipment operates in the same frequency bandwidth as industrial, scientific, and medical devices such as microwave ovens and mobile object identification RF-ID systems licensed premises radio stations and unlicensed specified low-power radio stations used in factory production lines.
The use of this device in a system operating either partially or completely outdoors may require the user to obtain a license for the system according to the Canadian regulations.
For further information, contact your local Industry Canada office. The rules for all access points are provided in both Chinese and English. Page Chinese Translation Chinese Translation English Translation Administrative Rules for Low-power Radio-Frequency Devices Article 12 For those low-power radio-frequency devices that have already received a type-approval, companies, business units or users should not change its frequencies, increase its power or change its original features and functions.
Page Regulatory Information Regulatory Information Figure 5 contains Brazil regulatory information for the access point models identified in the previous section.
Page 36 Cisco Website at www. A listing of Cisco's trademarks can be found at www. Third party trademarks mentioned are the property of their respective owners. This manual is also suitable for: Aironet series Air-apn-e-k9 Air-apn-e-k9 Air-apn-a-k9 Air-apn-a-k9. Print page 1 Print document 37 pages. Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password. Upload from disk. Upload from URL.
Cisco AIR-LAP1142N-A-K9 Getting Started Manual
Cisco Aironet 1140 Series Manuals
Cisco Aironet 1142 AIR-LAP1142N-S-K9 User Manual
Cisco Aironet 1140 Access Point AIR-AP1142N-E-K9 Data Sheet