Log in Become a member. DigiTech RP Product presentation. Subscribe to our free newsletter Subscribe. Write a user review Ask for a user review. Like Tweet Submit.

Author:Majind Zuluzragore
Language:English (Spanish)
Published (Last):17 August 2018
PDF File Size:9.26 Mb
ePub File Size:13.69 Mb
Price:Free* [*Free Regsitration Required]

Quick Links. Table of Contents. Page 4 1. The warranty registration card must be mailed within ten days after purchase date to validate this warranty.

DigiTech warrants this product, when used solely within the U. Page 7: Section One - Introduction If anything is missing, contact the factory at once. Please help us become acquainted with you and your needs by completing your warranty card or registering online at www.

It is your safeguard should a problem arise with your RP Performance mode provides access to all of the presets within the RP90 via the Up and Down Footswitches. Page 9 indicate whether you are sharp or flat. The left 6 red LEDs indicate the note is flat and should be tuned up. The right 6 red LEDs indicate the note is sharp and should be tuned down. The center LED indicates the note is in tune. The output is muted in Tuner mode; rock the Expression Pedal to regain volume. Page Presets Value Buttons 1.

Access the Tone Library 2. Access the Effects Library 3. Access the effects level with this button and select with this button and select with this button and adjust the a tone with the Value buttons. The Footswitch on the right will select the next preset up, and the Footswitch on the left will select the next preset down. Pressing both Footswitches together will bypass the currently selected preset.

Display The Display provides information for different functions depending on the mode that has been selected. In Performance mode, the Display shows the currently selected preset num- ber. Before connecting the RP90, make sure that the power to your amplifier and the RP90 is turned off. There is no power switch on the RP Connect one cable to the input of one amplifier, channel of a mixer, or power amp.

Connect the second cable to a second amplifier, second channel of a mixer, or power amp. Page Applying Power Applying Power Before applying power to anything, set your amp s to a clean tone and set the tone controls to a flat EQ response on most amps, this would be 0 or 5 on the tone controls. Then follow the steps listed below. When creating your own sound, you must first start with an existing preset. Changing presets, or turning the power off before storing any changes erases any edits made and the RP90 will revert to the stored values for the preset.

Press the Store button; the Preset number flashes. Press the Store button again to save your changes. Select a destination with the Footswitches. With stompboxes, the order in which they are connected affects the overall sound. The RP90 has placed the Amp and Effect models in an order for optimum results.

The EQ settings are: b1-b9 Bass tone control. The delayed signal is modulated in and out of tune and then mixed back with the original signal to create a thicker sound. Page Flanger Flanger A Flanger uses the same principle as a Chorus but uses a shorter delay time and adds regeneration or repeats to the modulating delay.

This results in an exaggerated up and down sweeping motion to the effect. Settings are F1-F9. Phaser A phaser splits the incoming signal, and then changes the phasing of the signal. Settings are Y1-Y9. Page Digitech Whammy As the Pedal is moved, the note bends either up or down. When DigiTech Whammy is selected, it is automatically placed before the Amp modeling as shown in the block diagram on page Settings are H1-H9.

Page Reverb Reverb Using reverb in recorded program material gives the listener a sense that the material is being performed in an actual room or hall. It is this similarity to actual acoustic spaces that makes rever- beration a useful tool in recorded music. Settings are: Reverb effect is turned off. The drum machine has the following parameters Drum Patterns Drum Tempo This calibration procedure is automatically entered after a factory reset procedure.

You can also initiate the calibration procedure by pressing and holding both Footswitches for approximately 5 seconds. This manual is also suitable for: Rp Print page 1 Print document 48 pages. Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password. Upload from disk. Upload from URL.


DigiTech RP90 Owner's Manual



All user reviews for the DigiTech RP90


Related Articles